Interlogix Monitor XL Hardware Guide Bedienungsanleitung PDF herunterladen (Seite 60)

56 Monitor ISM/xL™ Hardware Guide

22-0375 rev1.1

Appendix “A” 12VDC Relay

Dimensions: 1&3/8” (3.5cm) wide X 2&3/8” (6.0cm) long X 1&1/16“ (2.7cm) high.

Power:

12VDC, 8.5 mA active current rating.

Terminal Connections:

1. Normally Closed

2. Normally Open

3. Common

4. Positive Trigger

5. Negative 12VDC

6. Positive 12VDC

7. Negative Trigger

Features:

• Form “C” contact.

• Contact will change state when 12VDC applied to Pos. pin 6 and Neg. pin 5 and there is a wire short between

Pos. pin 6 and Pos. Trigger pin 4.

• When continuously powered by 12VDC, will change state when:

− Low voltage trigger applied to Pos. Trigger pin 4 (greater then 3VDC, approximately 130 micro amps).

− A negative supply is applied to Neg. Trigger pin 7.

− On board red LED turns on when relay activated.

Appendix “B” Wiring Specifications

• Earth Grounds:

Recommended:

18 AWG, stranded & insulated;

Good:

Standard 22 AWG quad cable (use all 4 wires).

• Module Bus (RS485) Cabling (device comms & power):

Recommended:

24 AWG, 4 conductors, Shielded Twisted Pair,

120

Ω impedance, low capacitance, 41 pF / meter or

12.5 pF / foot (such as Belden 9842).

ULC

: 22 AWG, 4 conductors, Shielded Twisted Pair, low capacitance.

For regions that require CE conformity, C-Tick conformity or the

equivalent the recommended Module Bus cabling bus wire type

must be used.

• Max. Length: Up to 610 m / 2000 ft. of cable on a Module bus port.

• NOTE: For longer cable distances, and/or where many expansion

modules are connected on one cable (daisy chained, star wiring

configurations are not acceptable) a 150 Ω ‘terminating’ resistor

will need to be installed across A and B communication terminals

of the last module on the ‘bus’ cable. If necessary, add a second resistor at the panel end module bus A and B if it is confirmed

that the panel connector is the “end of line” at that end.

• Separate Power (or door strike) Wiring:

Recommended:

18 AWG, stranded & insulated

(2 conductors; colour-coded is preferable);

Good:

22 AWG, 2 conductors, insulated.

• Inputs/Sensor Cabling:

22 AWG, 2-wires (For electrically noisy environments, use twisted pair, and/or shielded cable.)

• Outputs/Signalling: 22 AWG, 2 conductors.

• Reader Cabling: 24 AWG (ULC: 22 AWG), shielded (Max: 150 m / 500 ft.)

Basic reader (no LEDs, buzzer control, or tamper)

: 4 Conductors;

Reader with LED(s)

: 6 conductors;

Reader with LEDs, plus buzzer and tamper

: 9 conductors.

Modem/PC Link: Use kit provided, or 22/24 AWG low-cap cable (not reader cable). Shielded cable is recommended.

RS485 (shared cable or modem): 3 wires, see Module bus spec. above.

Red LED turns

on when relay

activated.

12345

12V Relay

P/N 650-0912

COM

+ve Trig

-ve 12VDC

+ve 12VDC

-ve Trig

non-energized

state.

Cabling P/Ns:

FT4

FT6

Module Bus (shielded)

Preferred (24 AWG): 120-3401 120-3405

ULC (22 AWG): 120-3408 120-3409

Note: Max. distance may be reduced with the ULC cable.

Reader cable (24 AWG shielded):

6 Conductors: 120-3402 120-3406

10 Conductors: 120-3403 120-3407

Note: ULC requires 22 AWG shielded cable.

Power (18 AWG): 120-3400 120-3404

I/O

(quad): 120-3410 120-3411

Notice: Elevator controller and

condominium keypad installations

include unique power and cabling

aspects. Always refer to the installation

instructions provided with each device.

Notice: Use minimum 26AWG UL/CSA/or

equivalent approved telephone cable.

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 66

Kommentare zu diesen Handbüchern

Keine Kommentare

Interlogix Monitor XL Hardware Guide Bedienungsanleitung Seite 60

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Schalttafel Interlogix Monitor XL Hardware Guide