Interlogix Monitor XL Hardware Guide Bedienungsanleitung Seite 53
- Seite / 66
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
22-0375 rev1.1 Monitor ISM/xL™ Hardware Guide 49
Procedure for Cold Booting the Main Control Board and Clearing Memory
1. Remove all power from main control board.
2. Insert the Program Reset Jumpers (CFG0 and CFG1) horizontally. See Program Reset Jumpers on the right side of the main
control module in the “Main Controller” diagram.
3. Apply AC Mains power.
4. The Status and Trouble LEDs will flash on and off together slowly.
5. Remove the 2 jumpers.
6. The same LEDs will momentarily flash rapidly together. (Controller processing)
7. The trouble light will turn off and only the Status LED will flash rapidly.
8. Proceed through the keypad log on procedure explained on page 4 and reset the config. as mentioned on page 4, lower 2
nd
column.
9. The keypad will display regular screens and only the Status LED will flash slowly to indicate a normal condition.
10. The memory has been returned to factory defaults. Reconnect all power.
Modems
North American Modem (Bell 103)
(P/N 650-3630)
Works to Feature set 3
World Wide Modem
(P/N 650-3633)
Works to Feature set 7
312 4
Seized Tip
Seized Ring
Tip
Ring
Off Hook
LED
Turns on when
unit dialing out.
Plugs into xL Main Control Board
Modem Expansion Socket
North American Modem
312 4
Seized Tip
Seized Ring
Tip
Ring
Off Hook LED
Turns on when
unit dialing out.
Plugs into xL Main Control Board
Modem Expansion Socket
World Wide Modem
756 8
0V
Line Failure
9312 4
Output 8
Output 7
Output 6
Output 5
Output 4
Output 3
Output 2
Output 1
To REDCARE Unit
01
1
2
3
2 vertical Jumpers in 1+2 = Output 8 will be 12VDC
high from 0V if main control board CPU fails
2 vertical Jumpers in 2+3 = Output 8 will be 0V low
from 12VDC high if main control board CPU fails
1 Jumper in 1+2 on left side =
Output 8 is a standard output #
8 on this board.
CPU
Failure
with
REDCARE
Interface
From REDCARE Unit
See “ENABLE LINE
FAILURE” next page.
STU (Subscriber Terminal Unit) Interface
REDCARE
(P/N 650-3631)
Feature Expansion Board
(P/N 650-3660)
Refer to Installation Instructions P/N 21-3612 for further
information.
756 8
0V
Line Failure
Plugs into xL Main Control Board
Modem Expansion Socket
9312 4
Output 8
Output 7
Output 6
Output 5
Output 4
Output 3
Output 2
Output 1
To REDCARE Unit
From
REDCARE Unit
See “ENABLE
LINE FAILURE”
next page.
STU Interface
REDCARE
STU (Subscriber Terminal Unit)
01
1
2
3
2 vertical Jumpers in 1+2 = Output 8 will be 12VDC
high from 0V if main control board CPU fails
2 vertical Jumpers in 2+3 = Output 8 will be 0V low
from 12VDC high if main control board CPU fails
1 Jumper in 1+2 on right side = Output 8
is a standard output # 8 on this board.
CPU
Failure
Feature Expansion Board
Feature Expansion Socket
Plugs into xL Main Control Board
Memory Expansion Socket
Refer to Installation Instructions P/N 21-3611 for further information.
Notice: Use minimum 26AWG UL/CSA/or
equivalent approved telephone cable.
- Monitor ISM/xL 1
- Hardware 1
- Contents 3
- Foreword 4
- Monitor ISM 5
- Main Control Board 6
- Enter ID: 7
- Arming Station Reader 8
- Keypad Command Entries 9
- No Commands (Simple Access) 10
- With Commands 10
- IMPORTANT: 11
- Refer to 11
- Ratings / Requirements 11
- 2 Zone Wiring cont 12
- 8 Zone Wiring and Mounting 14
- Adding an Electronic Siren 15
- 22-0375 rev1.1 16
- Output/Relay Card 17
- Version 1 18
- normally 19
- Testing (Signal Strength) 20
- Version 2 Wireless 21
- NA Module Notes 22
- Interface Board 23
- Receiver 23
- V2 Module Programming 25
- ” screen for editing. The 27
- Fire Module 28
- Features: 29
- Graphic Map Module cont 30
- Smart / Vigil Module 31
- Vigil Module 32
- Programming Inputs/Outputs 33
- Checking Status 34
- Door Controller Modules 36
- Version 2 Door Module 37
- Multi-Door 38
- Controller 38
- First Elevator 41
- Connections 41
- Elevator 42
- Elevator Isolator Board 43
- WATERPIPE 45
- Communication Modules 46
- IP Module V3 47
- Direct Connect to PC 49
- Monitor xL 51
- Main Controller 52
- Feature Expansion Board 53
- CPU Failure 54
- ComsLost #50624ef 55
- Enter code 55
- Input Point Expanders 56
- 8 Transistor 57
- Expansion 57
- Module Power Supply 58
- • AC Mains failure 59
- • Battery loss 59
- Single Device 61
- Multiple Device 61
- Control Panel as follows: 62
- Exit 63
Verwandte Produkte und Handbücher für Schalttafel Interlogix Monitor XL Hardware Guide
Schalttafel Interlogix NX-4 Bedienungsanleitung
(44 Seiten)
(44 Seiten)
Schalttafel Interlogix NX-4 Bedienungsanleitung
(18 Seiten)
(18 Seiten)
Schalttafel Interlogix NX-6 Bedienungsanleitung
(18 Seiten)
(18 Seiten)
Schalttafel Interlogix NX-8 Bedienungsanleitung
(61 Seiten)
(61 Seiten)
Schalttafel Interlogix NX-8 Bedienungsanleitung
(18 Seiten)
(18 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern