Interlogix NS3702-24P-4S User Manual Bedienungsanleitung

NS3702-24P-4S User Manual P/N 1072832 • REV 00.01 • ISS 14JUL14

10 1. INTRODUCTION NS3702-24P-4S - 24-Port 10/100/1000Mbps 802.3at PoE+ ports, 4-Port Shared Gi

100 The Page includes the following fields: Object Description  Source MAC Address The Sourc

101 The Page includes the following fields: .Object Description  Group ID Indicates the grou

102 Figure 4-5-4 : LACP Port Configuration Page Screenshot

103 The Page includes the following fields: Object Description  Port The switch port number.

104 4.5.3 LACP System Status This Page provides a status overview for all LACP instances. The

105 4.5.4 LACP Port Status This Page provides a status overview for LACP status for all ports.

106 Auto-refresh : Automatic refresh occurs every 3 seconds. 4.5.5 LACP Port Statistics This

107 4.6 VLAN 4.6.1 VLAN Overview A Virtual Local Area Network (VLAN) is a network topology conf

108 4.6.2 IEEE 802.1Q VLAN In large networks, routers are used to isolate broadcast traffic

109 allows Spanning Tree to be enabled on all ports and work normally. Some relevant terms: -

11 1.2 Product Description Ideal Solution for Secure IP Surveillance Construction Particularly

110 Port VLAN ID Packets that are tagged (are carrying the 802.1Q VID information) can

111 nor the host at the other end of the connection supports VLANs, then you should add this po

112  Tagged: Ports with tagging enabled will put the VID number, priority and other VLAN info

113 The Managed Switch supports multiple VLAN tags and can therefore be used in MAN applicatio

114 Object Description  Allowed Access VLANs This field shows the allowed Access VLANs, it o

115 Port VLAN Configuration The VLAN Port Configuration screen in Figure 4-6-2 appears. Figure

116  The VLANs that a trunk port is member of may be limited by the use of Allowed VLANs  Fr

117 tagged on egress, they will be tagged with a C-tag. S-Port: On ingress, frames with a VL

118 Untag All All frames, whether classified to the Port VLAN or not, are transmitted withou

119 Figure 4-6-4: VLAN Membership Status for Static User Page Screenshot

12 Intelligent Powered Device Alive-Checking The NS3702 can be configured to monitor connecte

120 The Page includes the following fields: Object Description  VLAN User A VLAN User is a m

121 uttons : Select VLAN Users from this drop down list. Auto-refresh : Check this box to refre

122 4.6.5 VLAN Port Status This Page provides VLAN Port Staus. The VLAN Port Status screen in F

123  Untagged VLAN ID Shows UVID (untagged VLAN ID). Port's UVID determines the packet&a

124 Figure 4-6-6 Private VLAN Membership Configuration page screenshot

125 The page includes the following fields: Object Description  Delete To delete a private V

126 database servers on the inside segment, but are not allowed to communicate with each other

127 This Page is used for enabling or disabling port isolation on ports in a Private VLAN. A po

128 4.6.8 VLAN setting example:  Separate VLAN  802.1Q VLAN Trunk  Port Isolate 4.6.8.1

129  Untagged packet entering VLAN 2 1. While [PC-1] transmit an untagged packet enters Port

13 Cost-Effective PoE Switch solution for IPv6 Networking Faced with the increasingly large

130 VLAN 3 : Port-4, Port-5 and Port-6 VLAN 1 : All other ports – Port-7~Port-28 Figure 4-6-10

131 other switches within the same VLAN group. The screen in Figure 4-6-12 appears. Figure 4

132 VLAN 3 : Port-4, Port-5 and Port-6 VLAN 1 : All other ports – Port-7~Port-48 Figure 4-6-14

133 Figure 4-6-15: VLAN Overlap Port Setting & VLAN 1 – The Public Area Member Assign Tha

134 Setup steps 1. Assign Port Mode Set Port-1~Port-4 in Isolate port. Set Port5 and Port-6 i

135 VLAN 3: Port-3~Port-6. The screen in Figure 4-6-18 appears. Figure 4-6-17: Private VLAN Po

136 4.6.9 MAC-based VLAN The MAC-based VLAN enties can be configured here. This Page allows for

137 : Click to add a new MAC-based VLAN entry. : Click to apply changes : Click to undo any c

138 4.6.11 Protocol-based VLAN This Page allows you to add new protocols to Group Name (unique

139 3. For SNAP: Valid value in this case also is comprised of two different sub-values. a.

14 1.3 How to Use This Manual This User’s Manual is structured as follows: Section 2, INSTALLAT

140 Figure 4-6-21: Group Name to VLAN Mapping Table Page Screenshot

141 The Page includes the following fields: Object Description  Delete To delete a Group Nam

142 4.7 Spanning Tree Protocol 4.7.1 Theory The Spanning Tree protocol can be used to detect an

143 STP communicates between switches on the network using Bridge Protocol Data Units (BPDUs).

144  Disabled – the port only responds to network management messages and must return to the

145 STP Operation Levels The Switch allows for two levels of operation: the switch level and th

146 The following are the user-configurable STP parameters for the switch level: Parameter Des

147 Port priority 128 Port cost 0 Bridge Priority 32,768 User-Changeable STA Parameters The

148 STP calculation of the most current Bridge and Port settings. Now, if switch A broadcasts

149 Figure 4-7-3: After Applying the STA Rules The switch with the lowest Bridge ID (switch C)

15 1.4 Product Features  Physical Port  24-Port 10/100/1000Base-T RJ-45 copper with IEEE 80

150 ‧ Extension – Multiple Spanning Tree Protocol (MSTP) : Defines an extension to RSTP to fur

151 Forwarding (used in STP compatible mode). Valid values are in the range 4 to 30 seconds -De

152 : Click to apply changes : Click to undo any changes made locally and revert to previousl

153 4.7.4 CIST Port Configuration This Page allows the user to inspect the current STP CIST po

154 Valid values are in the range 1 to 200000000.  Priority Controls the port priority. This

155 : Click to undo any changes made locally and revert to previously saved values. By default

156 4.7.5 MSTI Priorities This Page allows the user to inspect the current STP MSTI bridge inst

157 4.7.6 MSTI Configuration This Page allows the user to inspect the current STP MSTI bridge i

158 MSTI Mapping Object Description  MSTI The bridge instance. The CIST is not available fo

159 Figure 4-7-10 : MST1 MSTI Port Configuration Page Screenshot The Page includes the foll

16  STP, IEEE 802.1D Spanning Tree Protocol  RSTP, IEEE 802.1w Rapid Spanning Tree Protocol

160 values are in the range 1 to 200000000.  Priority Controls the port priority. This can be

161 AlternatePort BackupPort RootPort DesignatedPort Disable  CIST State The c

162  STP The number of legacy STP Configuration BPDU's received/transmitted on the port.

163 4.8 Multicast 4.8.1 IGMP Snooping The Internet Group Management Protocol (IGMP) lets host a

164 Figure 4-8-2: Multicast Flooding

165 Figure 4-8-3: IGMP Snooping Multicast Stream Control IGMP Versions 1 and 2 Multicast group

166 0x11 Specific Group Membership Query (if Group Address is Present) 0x16 Membership Report

167 Figure 4-8-4: IGMP State Transitions  IGMP Querier – A router, or multicast-enabled s

168 4.8.2 Profile Table This page provides IPMC Profile related configurations. The IPMC profil

169 profile by using the following buttons: : List the rules associated with the designated p

17  IEEE 802.1X Authentication with Guest VLAN  Built-in RADIUS client to cooperate with th

170  End Address The ending IPv4/IPv6 Multicast Group Address that will be used as an address

171 Figure 4-8-7: IGMP Snooping Configuration Page Screenshot The Page includes the following

172 unnecessary leave messages to the router side.  Proxy Enable Enable IGMP Proxy. This feat

173 4.8.5 IGMP Snooping VLAN Configuration Each Page shows up to 99 entries from the VLAN table

174 IGMPv2, Forced IGMPv3. Default compatibility value is IGMP-Auto.  PRI (PRI) Priority of I

175 Click "Save". The specific IGMP VLAN starts working after the corresponding stati

176 Object Description  Port The logical port for the settings.  Filtering Profile Select

177 The Page includes the following fields: Object Description  VLAN ID The VLAN ID of the e

178 Figure 4-8-9: IGMP Snooping Groups Information Page Screenshot The Page includes the foll

179 The IGMPv3 Information screen in Figure 4-8-12 appears. Figure 4-8-12: IGMP SSM Informatio

18 1.5 Product Specifications Product NS3702-24P-4S Hardware Specifications SFP/mini-GBIC Slo

180 4.8.10 MLD Snooping Configuration This Page provides MLD Snooping related configuration. Th

181  MLD SSM Range SSM (Source-Specific Multicast) Range allows the SSM-aware hosts and route

182 The Page includes the following fields: Object Description  Delete Check to delete the e

183 Buttons : Refreshes the displayed table starting from the "VLAN" input fields. :

184 Figure 4-8-15: MLD Snooping Port Group Filtering Configuration Page Screenshot

185 The Page includes the following fields: Object Description  Port The logical port for th

186 The Page includes the following fields: Object Description  VLAN ID The VLAN ID of the e

187 The "Start from VLAN", and "group" input fields allow the user to selec

188 Figure 4-8-18: MLD SSM Information Page Screenshot The Page includes the following fields

189 4.8.16 MVR (Multicaset VLAN Registration) The MVR feature enables multicast traffic forw

19 PD @ 15.4 watts 24 units PD @ 30.8 watts 14 units Layer 2 Functions Port Configuration Por

190 Figure 4-8-19: MVR Configuration Page Screenshot The Page includes the following fields:

191 Be Caution: MVR source ports are not recommended to be overlapped with management VLAN port

192 source ports. Subscribers cannot be directly connected to source ports.  Receiver: Config

193  IGMPv1 Joins Received The number of Received IGMPv1 Joins.  IGMPv2/MLDv1 Reports Recei

194 Object Description  VLAN VLAN ID of the group.  Groups Group ID of the group displayed

195 The Page includes the following fields: Object Description  VLAN ID VLAN ID of the group

196 4.9 Quality of Service 4.9.1 Understanding QoS Quality of Service (QoS) is an advanced t

197 3. Create a QoS profile which associates a service level and a classifier. 4. Apply a QoS

198 4.9.3 Port Classification This Page allows you to configure the basic QoS Ingress Classific

199 CoS is shown in parentheses after the configured default CoS.  DPL Controls the default d

2 Copyright © 2014 United Technologies Corporation Interlogix is part of UTC Building & In

20 Routing Protocols IPv4 software Static Routing IPv6 software Static Routing Management Funct

200 4.9.4 Port Scheduler This Page provides an overview of QoS Egress Port Schedulers for all s

201 4.9.5 Port Shaping This Page provides an overview of QoS Egress Port Shapers for all switch

202 4.9.5.1 QoS Egress Port Schedule and Shapers The Port Scheduler and Shapers for a specific

203  Queue Shaper Excess Controls whether the queue is allowed to use excess bandwidth.  Qu

204 Figure 4-9-6: QoS Egress Port Tag Remarking Page Screenshot

205 The Page includes the following fields: Object Description  Port The logical port for th

206 : Click to apply changes : Click to undo any changes made locally and revert to previousl

207  Classify Classification for a port have 4 different values.  Disable: No Ingress DSC

208 4.9.8 DSCP-based QoS This Page allows you to configure the basic QoS DSCP-based QoS Ingress

209  QoS Class QoS Class value can be any of (0-7)  DPL Drop Precedence Level (0-1)

21 RFC 3376 IGMP version 3 RFC 2710 MLD version 1 RFC 3810 MLD version 2 Environment Operating

210 4.9.9 DSCP Translation This Page allows you to configure the basic QoS DSCP Translation set

211 for QoS class and DPL map. There are two configuration parameters for DSCP Translation –

212 Object Description  QoS Class Available QoS Class value ranges from 0 to 7. QoS Class (0

213 Broadcast: Only Broadcast MAC addresses are allowedd. The default value is 'Any&a

214 4.9.11.1 QoS Control Entry Configuration The QCE Configuration screen in Figure 4-9-13 ap

215 or range(0-1, 2-3, 4-5, 6-7, 0-3, 4-7) or 'Any' DEI Drop Eligible Indicator:

216 Source IP IPv6 source address: (a.b.c.d) or 'Any', 32 LS bits DSCP Diffserv Cod

217 The Page includes the following fields: Object Description  User Indicates the QCL user.

218 'yes'. : Click to refresh the Page. 4.9.13 Storm Control Configuration Storm

219  Enable Controls whether the storm control is enabled on this switch port.  Rate Contro

22 2. INSTALLATION This section describes the hardware features and installation of the Managed

220 4.9.14 WRED This page allows you to configure the Random Early Detection (RED) settings f

221 This value is restricted to 0-100. RED Drop Probability Function The following illustratio

222 4.9.15 QoS Statistics This Page provides statistics for the different queues for all swit

223 4.9.16 Voice VLAN Configuration The Voice VLAN feature enables voice traffic forwarding o

224 The Page includes the following fields: Object Description  Mode Indicates the Voice

225  Port Discovery Protocol Indicates the Voice VLAN port discovery protocol. It will only w

226 4.9.17 Voice VLAN OUI Table Configure VOICE VLAN OUI table on this Page. The maximum entry

227 Buttons : Click to add a new access management entry. : Click to apply changes : Click to

228 4.10 Access Control Lists ACL is an acronym for Access Control List. It is the list table o

229 EType: The ACE will match Ethernet Type frames. Note that an Ethernet Type based ACE wil

23 Console Port The console port is a RJ-45 port connector. It is an interface for connecti

230 4.10.2 Access Control List Configuration This Page shows the Access Control List (ACL), whi

231 Permit: Frames matching the ACE may be forwarded and learned. Deny: Frames matching t

232 4.10.3 ACE Configuration Configure an ACE (Access Control Entry) on this Page. An ACE consi

233 The allowed range is 0x0 to 0xff.  Frame Type Select the frame type for this ACE. These f

234  MAC Parameters Object Description  SMAC Filter (Only displayed when the frame type is

235 specified (tag priority is "don't-care".)  ARP Parameters The ARP parame

236  Target IP Mask When "Network" is selected for the target IP filter, you can en

237 choose this value. A field for entering an IP protocol filter appears. ICMP: Select IC

238 Network: Source IP filter is set to Network. Specify the source IP address and source IP

239 specific value. The allowed range is 0 to 255. A frame that hits this ACE matches this IPv6

24 NS3702-24P-4S LED Indication Table  LED definition  System LED Color Function P

240 "don't-care"). Specific: If you want to filter a specific ICMP code filt

241  TCP/UDP Destination Number When "Specific" is selected for the TCP/UDP destina

242  Ethernet Type Parameters The Ethernet Type parameters can be configured when Frame Type

243 4.10.4 ACL Ports Configuration Configure the ACL parameters (ACE) of each switch port. Thes

244 value is "Disabled".  Logging Specify the logging operation of this port. The a

245 4.10.5 ACL Rate Limiter Configuration Configure the rate limiter for the ACL of the switch.

246 4.11 Authentication This section is to control the access of the Managed Switch, includes t

247 3rd party switch or a hub) and still require individual authentication, and that the client

248 Figure 4-11-1  Client—the device (workstation) that requests access to the LAN and switc

249 header is removed, leaving the EAP frame, which is then encapsulated for Ethernet and sent

25 2.1.3 Switch Rear Panel The rear panel of the Managed Switch indicates an AC inlet power soc

250  Ports in Authorized and Unauthorized States The switch port state determines whether

251 Figure 4-11-3: Authentication Method Configuration Page Screenshot

252 The Page includes the following fields: Object Description  Client The management client

253 Figure 4-11-4: Network Access Server Configuration Page Screenshot The Page includes the f

254 Enabled after the interval specified by the Reauthentication Period. Reauthentication for 8

255 Single 802.1X Multi 802.1X MAC-Based Auth. If a client is denied access - either b

256 The "Guest VLAN Enabled" checkbox provides a quick way to globally enable/disable

257 authentication. Force Unauthorized In this mode, the switch will send one EAPOL Failure fr

258 EAPOL Start frame retransmission rate. Single 802.1X In port-based 802.1X authentication,

259 supplicants that might be on the port. The maximum number of supplicants that can be attach

26 2.2 Installing the Switch This section describes how to install your Managed Switch and make

260 supplicant is successfully authenticated. If present and valid, traffic received on the sup

261 For trouble-shooting VLAN assignments, use the "Monitor→VLANs→VLAN Membership and VLAN

262 transmission of EAPOL Request Identity frames is configured with EAPOL Timeout. If Allow Gu

263 port and will not cause the clients to get temporarily unauthorized. Reinitialize: Force

264 4.11.4 Network Access Overview This Page provides an overview of the current NAS port state

265 is not overridden by NAS. If the VLAN ID is assigned by the RADIUS server, "(RADIUS-as

266  QoS Class The QoS class assigned by the RADIUS server. The field is blank if no QoS clas

267 mesRx frames that have been received by the switch. Rx Logoff dot1xAuthEapolLogoffFramesRx

268 MAC-based Auth. Direction Name IEEE Name Description Rx Access Challenges dot1xAuth

269 Failures Fails Counts the number of times that the switch receives a failure message. This

27 Connection to the Managed Switch requires UTP Category 5e network cabling with RJ-45 tips.

270 Address rameSource VLAN ID - The VLAN ID on which the last frame from the last supplicant/

271 Selected Counters Object Description  Selected Counters The Selected Counters table is v

272 : This button is available in the following modes: • Force Authorized • Force Unauthorized

273 Figure 4-11-7: RADIUS Server Configuration Page Screenshot The Page includes the followin

274  Key The secret key - up to 63 characters long - shared between the RADIUS server and the

275 : Click to undo the addition of the new server. : Click to apply changes : Click to undo

276 trying to contact a server that it has already determined as dead. Setting the Deadtime to

277 4.11.8 RADIUS Overview This Page provides an overview of the status of the RADIUS servers c

278 been disabled, but will get re-enabled when the dead-time expires. The number of seconds le

279 4.11.9 RADIUS Details This Page provides detailed statistics for a particular RADIUS server

28 Step 5: After the brackets are attached to the Managed Switch, use suitable screws to secure

280 counters. Direction Name RFC4668 Name Description Rx Access Accepts radiusAuthClientExtA

281 dropped for some other reason. Rx Packets Dropped radiusAuthClientExtPacketsDropped The num

282 counted as a retransmit as well as a timeout. A send to a different server is counted as a

283 between the backend servers to show details for. Object Description RADIUS accounting serv

284 Tx Retransmissions radiusAccClientExtRetransmissions The number of RADIUS packets retransmi

285 accounting attempts.  Dead (X seconds left): Accounting attempts were made to this server

286 Figure 4-11-11: RADIUS Server Configuration Screenshot

287 2. Add New RADIUS Cleint on the Windows 2003 server Figure 4-11-12: Windows Server – Add

288 Figure 4-11-13: Windows Server RADIUS Server Setting 4. The shared secret key should be as

289 5. Configure ports attribute of 802.1X, the same as “802.1X Port Configuration”. Figure

29  Approved IFS SFP Transceivers NS3702 Managed Switch supports both single mode and m

290 Figure 4-11-17: Add User Properties Screen Figure 4-11-18: Add User Properties Screen

291 Set the Port Authenticate Status to “Force Authorized” if the port is connected to the RAD

292 4. Select “Authentication” tab. 5. Select “Enable network access control using IEEE 802.

293 Figure 4-11-21: Windows Client Popup Login Request Message 9. Enter the user name, passwo

294 4.12 Security This section is to control the access of the Managed Switch, includes the use

295 Figure 4-12-1: Port Limit Control Configuration Overview Page Screenshot The Page include

296  Aging Period If Aging Enabled is checked, then the aging period is controlled with this

297 available MAC addresses.  Action If Limit is reached, the switch can take one of the foll

298 non-committed changes will be lost.

299 Buttons : Click to apply changes : Click to undo any changes made locally and revert to p

3 TABLE OF CONTENTS 1. INTRODUCTION...

30 1. It is recommended to use IFS SFPs on the Managed Switch. If you insert an SFP transceiv

300 host IP address matched the entry.  SNMP Indicates the host can access the switch from SN

301 Buttons Auto-refresh : Check this box to refresh the Page automatically. Automatic refres

302 4.12.4 HTTPs Configure HTTPS on this Page. The HTTPS Configuration screen in Figure 4-12-4

303 port is set-up for software-based learning. In this mode, frames from unknown MAC addresses

304 Figure 4-12-6: Port Security Status Screen Page Screenshot The Page includes the followin

305 Object Description  Port The port number for which the status applies. Click the port nu

306 4.12.7 Port Security Detail This Page shows the MAC addresses secured by the Port Security

307 4.12.8 DHCP Snooping DHCP Snooping is used to block intruder on the untrusted ports of DUT

308 Figure 4-12-8: DHCP Snooping Configuration Screen Page Screenshot The Page includes the fo

309 : Click to apply changes : Click to undo any changes made locally and revert to previousl

31 Figure 2-2-5: How to Pull Out the SFP/SFP+ Transceiver Never pull out the module without

310 Figure 4-12-10: IP Source Guard Configuration Screen Page Screenshot The Page includes th

311 that are matched in static entries on the specific port. Buttons : Click to translate all

312 4.12.12 ARP Inspection ARP Inspection is a secure feature. Several types of attacks can be

313 The Page includes the following fields: Object Description  Mode of ARP Inspection Confi

314 4.12.13 ARP Inspection Static Table This Page provides Static ARP Inspection Table. The Sta

315 4.13 Address Table Switching of frames is based upon the DMAC address contained in the fram

316 Aging Configuration By default, dynamic entries are removed from the MAC table after 300 se

317 Buttons : Click to apply changes : Click to undo any changes made locally and revert to p

318 The Page includes the following fields: Object Description  Type Indicates whether the

319 Page" input field. When first visited, the web Page will show the first 20 entries fro

32 3. SWITCH MANAGEMENT This chapter explains the methods that you can use to configure managem

320 Figure 4-13-4: Dynamic IP Source Guard Table Screenshot Navigating the ARP Inspection Tab

321 Buttons Auto-refresh : Check this box to refresh the Page automatically. Automatic refresh

322 4.14 LLDP 4.14.1 Link Layer Discovery Protocol Link Layer Discovery Protocol (LLDP) is us

323 Figure 4-14-1: LLDP Configuration Page Screenshot The Page includes the following fields: L

324  Port The switch port number of the logical LLDP port.  Mode Select LLDP mode.  Rx

325  System Description Optional TLV: When checked the "system description" is incl

326 The Page includes the following fields: Fast start repeat count Object Description  Fas

327 Object Description  Latitude Latitude SHOULD be normalized to within 0-90 degrees with a

328 or US.  State National subdivisions (state, canton, region, province, prefecture).  Cou

329 Emergency Call Service (e.g. E911 and others), such as defined by TIA or NENA. Object Desc

33 3.2 Management Access Overview The Managed Switch gives you the flexibility to access and ma

330 LAN. Object Description  Delete Check to delete the policy. It will be deleted during th

331 applications relying on TCP with buffering would not be an intended use of this application

332 Object Description  Port The port number for which the configuration applies.  Policy

333 Devices. An LLDP-MED Network Connectivity Device is a LAN access device based on any of the

334 LLDP-MED Communication Endpoint (Class III) The LLDP-MED Communication Endpoint (Class II

335  Video Conferencing - for use by dedicated Video Conferencing equipment and other similar

336  Auto-negotiation Capabilities Auto-negotiation Capabilities shows the link partners MAC/

337 4. WLAN Access Point 5. Router 6. Telephone 7. DOCSIS cable device 8. Station only 9. Reser

338 Figure 4-14-5: LLDP Statistics Page Screenshot The Page includes the following fields: Gl

339 The displayed table contains a row for each port. The columns hold the following informatio

34 3.3 Administration Console The administration console is an internal, character-oriented, an

340 4.15 Network Diagnostics This section provide the Physical layer and IP layer network diagn

341 4.15.1 Ping This Page allows you to issue ICMP PING packets to troubleshoot IP connectivity

342 4.15.2 IPv6 Ping This Page allows you to issue ICMPv6 PING packets to troubleshoot IPv6 con

343 4.15.3 Remote IP Ping Test This Page allows you to issue ICMP PING packets to troubleshoot

344 : Click to undo any changes made locally and revert to previously saved values. : Clears th

345 The Page includes the following fields: Object Description  Port The port where you are

346 4.16 Power over Ethernet Providing up to 24 PoE, in-line power interfaces, the NS3702-24P-4

347 3~12 Watts PoE Splitter PoE Splitter split the PoE 52V DC over the Ethernet cable into 5/1

348  Classification mode In this mode each port automatic determines how much power to reserv

349 Figure 4-16-2: PoE Configuration Screenshot

35 connected and monitor the system during system reboots. Also, certain error messages are sen

350 The page includes the following fields: Object Description  System PoE Admin Mode Allows

351 A PD will return to Class 0 to 4 in accordance with the maximum power draw as specified by

352 Buttons : Click to apply changes : Click to undo any changes made locally and revert to

353  Disable: disable PoE function.  Schedule: enable PoE function in schedule mode.  Sch

354 4.16.6 PoE Status This page allows the user to inspect the total power consumption, total p

355 Figure 4-16-5:PoE Status Screenshot

356 The page includes the following fields: Object Description  Sequential Power On Displays

357 4.16.7 PoE Schedule This page allows the user to define PoE schedule and schedule power rec

358 The screen in Figure 4-16-6 appears. Figure 4-16-6: PoE Schedule Screenshot Please press

359 Object Description  Profile Set the schedule profile mode. Possible profiles are:  Pro

36 3.5 SNMP-based Network Management You can use an external SNMP-based application to config

360 Figure 4-16-7: LLDP PoE Neighbour Screenshot Please be noticed that administrator has to

361 This page provides you with how to configure PD Alive Check.The screen in Figure 4-16-9 ap

362  Reboot & Alarm: It means system will reset the PoE port and issue an alarm message vi

363 4.16.10 Port Power Consumption This page allows user to see the usage of individual PoE Por

364 4.17 Loop Protection This chapter describes enabling loop protection function that provides

365 The Page includes the following fields: General Settings Object Description  Enable Loop

366 4.17.2 Loop Protection Status This Page displays the loop protection port status of the swi

367 4.18 RMON RMON is the most important expansion of the standard SNMP. RMON is a set of MIB d

368  InUcastPkts: The number of uni-cast packets delivered to a higher-layer protocol.  InN

369 : Click to add a new community entry. : Click to apply changes : Click to undo any change

37 4. WEB CONFIGURATION This section introduces the configuration and functions of the Web-base

370 : Click to refresh the Page immediately. Auto-refresh : Check this box to refresh the Page

371 Buttons : Click to add a new community entry. : Click to apply changes : Click to undo an

372 4.18.4 RMON Event Status This Page provides an overview of RMON Event table entries.Each Pa

373 4.18.5 RMON History Configuration Configure RMON History table on this Page. The entry inde

374 4.18.6 RMON History Status This Page provides an detail of RMON history entries; screen in

375  Jabb. The number of frames which size is larger than 64 octets received with invalid CR

376 Buttons : Click to add a new community entry. : Click to apply changes : Click to undo an

377 but including FCS octets) of between 64 and 1518 octets.  Undersize The total number of p

378 5. SWITCH OPERATION 5.1 Address Table The Managed Switch is implemented with an address tab

379 The Managed Switch performs "Store and Fforward" therefore, no error packets oc

38 2. When the following login screen appears, please enter the default username "admin&q

380 6. Power over Ethernet Overview What is PoE? The PoE is an abbreviation of Power over Ether

381 specification allows two options for using these cables for power, shown in Figure 1 and Fi

User’s Manual of NS3702-24P-4S 7. TROUBLESHOOTING This chapter contains information to help you solve issues. If the Managed Switch is not functionin

User’s Manual of NS3702-24P-4S APPENDIX A: Networking Connection A.1 PoE RJ-45 Port Pin Assignments PIN NO RJ-45 POWER ASSIGNMENT 1  Power + 2  P

User’s Manual of NS3702-24P-4S A.3 10/100Mbps, 10/100Base-TX When connecting your Switch to another Fast Ethernet switch, a bridge or a hub, a straig

User’s Manual of NS3702-24P-4S The standard cable, RJ-45 pin assignment 2 1 3 6 12362 1 3 6 The standard RJ-45 receptacle/connector There are 8

386 APPENDIX B : GLOSSARY A ACE ACE is an acronym for Access Control Entry. It describes acc

387 See the Web Page help text for each specific port property. ACL|Rate Limiters: Under this

388 Auto-Negotiation Auto-negotiation is the process where two different devices establish th

389 DHCP used by networked computers (clients) to obtain IP addresses and other parameters such

39 Figure 4-1-3: Web Main Page Now, you can use the Web management interface to continue the

390 DoS is an acronym for Denial of Service. In a denial-of-service (DoS) attack, an attacker a

391 HTTP HTTP is an acronym for Hypertext Transfer Protocol. It is a protocol that used to tr

392 credentials for authentication from any point within the network. IGMP IGMP is an acron

393 IPMC is an acronym for IP MultiCast. IP Source Guard IP Source Guard is a secure feature u

394 administrator wants to do a fixed mapping between the DMAC address and switch ports. The

395 credentials are valid. Based on the answer, the NAS then allows or disallows access to the

396 OUI is the organizationally unique identifier. An OUI address is a globally unique identifi

397 An alternative protocol is Internet Message Access Protocol (IMAP). IMAP provides the user

398 Q QCE QCE is an acronym for QoS Control Entry. It describes QoS class associated with a

399 R RARP RARP is an acronym for Reverse Address Resolution Protocol. It is a protocol that

4 4.2.2 IP Configuration...

40 4.1 Main Web Page The Managed Switch provides a Web-based browser interface for configuring

400 (known as a message digest) of an input data sequence (the message) of any length. Shaper

401 strong authentication or guarantee confidentiality (Wikipedia). SSM SSM In SyncE this is

402 TELNET is an acronym for TELetype NETwork. It is a terminal emulation protocol that uses th

403 UDP provides two services not provided by the IP layer. It provides port numbers to help di

404 W WEP WEP is an acronym for Wired Equivalent Privacy. WEP is a deprecated algorithm to sec

405 (Wikipedia). WRES WRED is an acronym for Weighted Random Early Detection. It is an active

41 those listed in the Main Function. The screen in Figure 4-1-5 appears. Figure 4-1-5: Manage

42 4.2 System Use the System menu items to display and configure basic administrative details o

43 4.2.1 System Information The System Infomation Page provides information for the current dev

44  Software Version The software version of the Managed Switch.  Software Date The date wh

45 mode traffic is routed between all interfaces. DNS Server This setting controls the DNS na

46 Mask Length The destination IP network or host mask, in number of bits (prefix length). Gate

47 Figure 4-2-3: IP Status Page Screenshot The Page includes the following fields: Object Desc

48 refer to each group privilege level. User's privilege should be same or greater than th

49 groups, i.e. that is granted the fully control of the device. But others value need to refer

5 4.4.1 Port Configuration...

50 If you forget the new password after changing the default password, please press the “Rese

51 4.2.5 Privilege Levels This Page provides an overview of the privilege levels. After setup i

52 The Page includes the following fields: Object Description  Group Name The name identif

53 4.2.6 NTP Configuration Configure NTP on this Page. NTP is an acronym for Network Time Proto

54 4.2.7 Time Configuration Configure Time Zone on this Page. A Time Zone is a region that has

55 to identify the time zone. ( Range : Up to 16 characters )  Daylight Saving Time This is

56 Figure 4-2-10: UPnP Configuration Page Screenshot The Page includes the following fields:

57 Figure 4-2-11: UPnP devices show on Windows My Network Place 4.2.9 DHCP Relay Configure

58 screen in Figure 4-2-12 appears. Figure 4-2-12 DHCP Relay Configuration Page Screenshot Th

59  Drop: Drop the package when receiving a DHCP message that already contains relay informat

6 4.7.9 Port Statistics...

60  Receive Bad Circuit ID The packets number that the Circuit ID option did not match known

61 4.2.11 CPU Load This Page displays the CPU load, using a SVG graph. The load is measured as

62 4.2.12 System Log The Managed Switch system log information is provided here. The System Log

63 : Hides the selected log entries. : Downloads the selected log entries. : Updates the system

64 : Updates the system log entry to the previous available entry ID. : Updates the system log

65 Buttons : Click to apply changes : Click to undo any changes made locally and revert to pr

66 4.2.15 SMTP Configuration This Page facilitates an SMTP Configuration on the switch. The SMT

67 Buttons : Send a test mail to mail server to check this account is available or not. : Clic

68 DO NOT Power OFF the Managed Switch until the update progress is complete. Do not quit th

69 Do not quit the Firmware Upgrade Page without pressing the “OK” button after the image is l

7 4.9.12 QCL Status ...

70 Figure 4-2-24: Configuration Download Page Screenshot 4.2.20 Configuration Upload Configura

71 4.2.21 Configuration Activate Configuration Activate page allows to activate the startup-co

72 4.2.23 Image Select This Page provides information about the active and alternate (backup)

73 Object Description  Image The flash index name of the firmware image. The name of primary

74 Figure 4-2-30: System Reboot Page Screenshot Buttons : Click to reboot the system. : Click

75 SNMP Operations SNMP itself is a simple request/response protocol. NMSs can send multiple

76 4.3.2 SNMP System Configuration Configure SNMP on this Page. The SNMP System Configuration s

77 SNMP version is SNMPv3, the community string will be associated with SNMPv3 communities tabl

78 4.3.3 SNMP Trap Configuration Configure SNMP trap on this Page. The SNMP Trap Configuration

79  Trap Community Indicates the community access string when send SNMP trap packet. The allo

8 4.12.12 ARP Inspection ...

80  System Enable/disable that the Interface group's traps. Possible traps are:  Warm

81  System Name An administratively assigned name for this managed node. By convention, this

82 SNMPv1 or SNMPv2c community string.  Source IP Indicates the SNMP access source address. A

83 engine with which this user can communicate. In other words, if user engine ID equal system

84 : Click to add a new user entry. : Click to apply changes : Click to undo any changes made

85 : Click to apply changes : Click to undo any changes made locally and revert to previously

86 : Click to undo any changes made locally and revert to previously saved values. 4.3.5.5 SNM

87  Write View Name The name of the MIB view defining the MIB objects for which this request

88 4.4 Port Management Use the Port Menu to display or configure the Managed Switch's port

89 red that it is down.  Current Link Speed Provides the current link speed of the port.  C

9 4.18.1 RMON Alarm Configuration ...

90 4.4.2 Port Statistics Overview This Page provides an overview of general traffic statistic

91 4.4.3 Port Statistics Detail This Page provides detailed traffic statistics for a specific s

92  Rx and Tx Broadcast The number of received and transmitted (good and bad) broadcast packe

93 : Clears the counters for all ports. Auto-refresh : Check this box to enable an automatic

94  Distance(m) Display the supports distance of current SFP module, the distance value is ge

95 Figure 4-4-7: Port Mirror Application The traffic to be copied to the mirror port is selec

96 Figure 4-4-8: Mirror Configuration Page Screenshot The Page includes the following fields:

97 Buttons : Click to apply changes : Click to undo any changes made locally and revert to pr

98 Figure 4-5-1: Link Aggregation The Link Aggregation Control Protocol (LACP) provides a stan

99  Enable the link aggregation prior to connecting any cable between the switches to avoid c