Interlogix TVT-4101 Bedienungsanleitung PDF herunterladen (Seite 1)

P/N 1072700B-EN • REV 1.0 • ISS 17OCT13 1 / 2

TruVision TVT-2101/ TVT-4101 IR Turret

Camera Installation Instructions

Figure 1: Parts of the camera

A. Video cable

B. Power cable

C. Mounting bracket

D. Fixed ring

E. Shroud

F. Camera

Figure 2: Camera front

LED IR lights; B. Lens; C. Light sensor

Overview

These are the TruVision IR Turret Camera installation

instructions for TVT-2101/4101. The instructions describe a

standard installation.

The camera consists of the following:

 Camera with power and video output cables

 Camera shroud

 Fixed ring to secure the camera and camera shroud to the

mounting bracket

 One dual-power terminal block with its screw and anchor

 4 anchors and 4 screws for wall or ceiling installation

Refer to Figures 1 and 2 when performing the camera setup

procedures.

Installation

When installing the camera, please use the mounting bracket

as a template.

To install the camera:

1. Unscrew the fixed ring and shroud assembly from the

camera.

2. Using the mounting bracket as a template, place it level

against the mounting surface and mark the position of the

mounting holes.

3. Following all local codes, drill and prepare the mounting

holes.

4. Route the camera’s cable through the mounting bracket,

and then install the mounting bracket with the four

provided screws. If your mounting surface requires it, use

the provided wall anchors or other appropriate fasteners.

5. While holding the camera in position, place the fixed ring

and shroud over the camera and tighten.

6. Adjust the camera position.

7. Connect a 75-ohm coaxial video cable to the camera’s

video cable, and connect a 12 VDC power supply to the

power cable.

Note: When installing the camera, tilting the camera housing

past 80° may result in reflection of IR illumination from the

camera base into the lens. This can distort or obscure the

picture in night mode.

8. Check the picture and adjust the camera position and

angle as required.

9. Tighten the fixed ring to secure it to the mounting bracket.

Ensure that the camera shroud is firmly attached to the

bracket.

Specifications

Power supply 12 VDC

Current 80 mA (IR Off)

200 mA (IR On)

Power consumption 2.4 W max.

Weight 0.86 lb. (390 g)

Dimensions (H × Ø) 2.7 x 3.7 (69 x 94 mm)

1 2

Inhaltsverzeichnis

Seite 1 - Specifications

P/N 1072700B-EN • REV 1.0 • ISS 17OCT13 1 / 2 TruVision TVT-2101/ TVT-4101 IR Turret Camera Installation Instructions Figure 1: Parts of the camera

Seite 2 - Contact information

2 / 2 P/N 1072700B-EN • REV 1.0 • ISS 17OCT13 Regulatory information Manufacturer United Technologies Corporation. 2955 Red Hill Avenue, Costa M

Verwandte Modelle: TVT-2101

Kommentare zu diesen Handbüchern

Keine Kommentare

Interlogix TVT-4101 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Videoüberwachungssysteme Interlogix TVT-4101 herunter. Interlogix TVT-4101 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: TVT-2101

Kommentare zu diesen Handbüchern

Interlogix TVT-4101 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Videoüberwachungssysteme Interlogix TVT-4101 herunter. Interlogix TVT-4101 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: TVT-2101

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Videoüberwachungssysteme Interlogix TVT-4101